$INCLUDE_FILE


(* GLOBALE TYPEN *)



(* PROJEKT TYPEN *)

TYPE FAU_OUT:STRUCT	
		WVCS     		:INT ; (*水阀控制转换值，放大100倍*)
		VFCS   			:INT;  (*变频控制*)	
		FVCS	        :INT ; (*风阀控制 (50~100)*)	
		FDO	            :BOOL; (*风阀开控制*)
		FDS	            :BOOL; (*风阀关控制*)
		Control         :BOOL; (*启停控制*)
		RH        		:REAL; (*运行小时*)
		SN        		:INT ; (*设备状态代码*)	
	END_STRUCT;
END_TYPE

TYPE FAU_IN:STRUCT
		SM              :INT ; (*季节模式 0夏季 1冬季 2过渡 *)
		LM              :BOOL; (*逻辑联动模式 0无联动 1联动 *)
		Run             :BOOL; (*运行状态*)
		Fault           :BOOL; (*故障状态*)
		Auto            :BOOL; (*自动状态*)
		Control         :BOOL; (*程序控制*)
		FDOB            :BOOL; (*风阀开状态*)
		FDSB            :BOOL; (*风阀关状态*)	
		FVMC			:BOOL; (*风阀手动控制*)
		FVMV    		:INT ; (*风阀手动控制值*)
		FVOCT			:TIME; (*风阀开启时间周期设定OpenCycleTime*)
		FVOST			:TIME; (*风阀开启稳定时间设定OpenStableTime*)	
		TSET			:REAL; (*温度设定*)
		WVMC			:BOOL; (*水阀手动控制*)
		WVMV    		:REAL; (*水阀手动控制值*)
		VFMC    		:BOOL; (*变频手动控制值*)
		VFMV            :INT;  (*变频手动控制值*)
		STS         	:REAL; (*送风温度*)
		RST      		:BOOL; (*运行时间累计重置*)
		RSTV			:REAL; (*运行时间累计重置值*)
		FPS 			:BOOL; (*风机压差*)
		IPS 			:BOOL; (*滤网压差*)
		AFS 			:BOOL; (*低温断路开关*)
		ISO1   			:BOOL; (*运行故障反馈隔离*)
		ISO2   			:BOOL; (*风机压差反馈隔离*)
		ISO3   			:BOOL; (*低温断路报警隔离*)	
		VP				:REAL; (*PI设定值P*) 
		VI				:REAL; (*PI设定值I*)
		FDELAY			:TIME; (*风机启动延时*)
		VDELAY			:TIME; (*风阀信号切除延时*)
		
	END_STRUCT;
END_TYPE



(* GLOBALE PROTOTYPEN *)



(* PROJEKT PROTOTYPEN *)

$INCLUDE "C:\PROGRAM FILES (X86)\BRAINCONTROL\EXDRIVE\EXCONFIG\EXDRIVE\LIB\BRCON_MCFB_ED_V3.3.0.1\$GEN$\BS_SCALE.PTT"
$INCLUDE "C:\PROGRAM FILES (X86)\BRAINCONTROL\EXDRIVE\EXCONFIG\EXDRIVE\LIB\BRCON_MCFB_ED_V3.3.0.1\$GEN$\IJ_EAFGROUP.PTT"
$INCLUDE "C:\PROGRAM FILES (X86)\BRAINCONTROL\EXDRIVE\EXCONFIG\EXDRIVE\LIB\BRCON_MCFB_ED_V3.3.0.1\$GEN$\BS_AVERAGE.PTT"
$INCLUDE "C:\PROGRAM FILES (X86)\BRAINCONTROL\EXDRIVE\EXCONFIG\EXDRIVE\LIB\BRCON_MCFB_ED_V3.3.0.1\$GEN$\IJ_FAU.PTT"
$INCLUDE "C:\PROGRAM FILES (X86)\BRAINCONTROL\EXDRIVE\EXCONFIG\EXDRIVE\LIB\BRCON_MCFB_ED_V3.3.0.1\$GEN$\IJ_LSYNCCONTROL.PTT"


(* EXTERNE POEs *)



$END_INCLUDE_FILE